View CA308306_1223857.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
CA3083
Data Sheet February 7, 2006 FN481.6
General Purpose High Current NPN Transistor Array
The CA3083 is a versatile array of five high current (to 100mA) NPN transistors on a common monolithic substrate. In addition, two of these transistors (Q1 and Q2) are matched at low current (i.e., 1mA) for applications in which offset parameters are of special importance. Independent connections for each transistor plus a separate terminal for the substrate permit maximum flexibility in circuit design.
Features
* High IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mA (Max) * Low VCE sat (at 50mA). . . . . . . . . . . . . . . . . . . 0.7V (Max) * Matched Pair (Q1 and Q2) - VIO (VBE Match) . . . . . . . . . . . . . . . . . . . . . 5mV (Max) - IIO (at 1mA) . . . . . . . . . . . . . . . . . . . . . . . . 2.5A (Max) * 5 Independent Transistors Plus Separate Substrate Connection * Pb-Free Plus Anneal Available (RoHS Compliant)
Ordering Information
PART NUMBER CA3083 CA3083Z (Note) CA3083M96 CA3083MZ (Note) TEMP. RANGE PART (C) MARKING CA3083 CA3083Z 3083 3083MZ PACKAGE PKG. DWG. # E16.3
Applications
* Signal Processing and Switching Systems Operating from DC to VHF * Lamp and Relay Driver * Differential Amplifier * Temperature Compensated Amplifier * Thyristor Firing * See Application Note AN5296 "Applications of the CA3018 Circuit Transistor Array" for Suggested Applications
-55 to 125 16 Ld PDIP
-55 to 125 16 Ld PDIP* (Pb-free) E16.3 -55 to 125 16 Ld SOIC Tape and Reel M16.15
-55 to 125 16 Ld SOIC (Pb-Free) M16.15 -55 to 125 16 Ld SOIC (Pb-Free) M16.15 Tape and Reel
CA3083MZ96 3083MZ (Note)
*Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
Pinout
CA3083 (PDIP, SOIC) TOP VIEW
1 2 3 4 SUBSTRATE 5 6 Q3 7 8 Q4 10 9 Q5 16 15 14 13 12 11
Q1 Q2
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 1998, 2005, 2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners.
CA3083
Absolute Maximum Ratings
The following ratings apply for each transistor in the device: Collector-to-Emitter Voltage, VCEO . . . . . . . . . . . . . . . . . . . . . . 15V Collector-to-Base Voltage, VCBO. . . . . . . . . . . . . . . . . . . . . . . . 20V Collector-to-Substrate Voltage, VCIO (Note 1). . . . . . . . . . . . . . 20V Emitter-to-Base Voltage, VEBO . . . . . . . . . . . . . . . . . . . . . . . . . . 5V Collector Current (IC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mA Base Current (IB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA
Thermal Information
Thermal Resistance (Typical, Note 2) JA (C/W) JC (C/W) PDIP Package . . . . . . . . . . . . . . . . . . . 135 N/A SOIC Package . . . . . . . . . . . . . . . . . . . 200 N/A Maximum Power Dissipation (Any One Transistor) . . . . . . . 500mW Maximum Junction Temperature (Plastic Package) . . . . . . . 150C Maximum Storage Temperature Range . . . . . . . . . -65C to 150C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300C (SOIC - Lead Tips Only)
Operating Conditions
Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . .-55C to 125C
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES: 1. The collector of each transistor of the CA3083 is isolated from the substrate by an integral diode. The substrate must be connected to a voltage which is more negative than any collector voltage in order to maintain isolation between transistors and provide normal transistor action. To avoid undesired coupling between transistors, the substrate Terminal (5) should be maintained at either DC or signal (AC) ground. A suitable bypass capacitor can be used to establish a signal ground. 2. JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
PARAMETER FOR EACH TRANSISTOR
For Equipment Design, TA = 25C SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Collector-to-Base Breakdown Voltage Collector-to-Emitter Breakdown Voltage Collector-to-Substrate Breakdown Voltage Emitter-to-Base Breakdown Voltage Collector-Cutoff-Current Collector-Cutoff-Current DC Forward-Current Transfer Ratio (Note 3) (Figure 1)
V(BR)CBO V(BR)CEO V(BR)CIO V(BR)EBO ICEO ICBO hFE
IC = 100A, IE = 0 IC = 1mA, IB = 0 ICI = 100A, IB = 0, IE = 0 IE = 500A, IC = 0 VCE = 10V, IB = 0 VCB = 10V, IE = 0 VCE = 3V IC = 10mA IC = 50mA
20 15 20 5 40 40 0.65 -
60 24 60 6.9 76 75 0.74 0.40 450
10 1 0.85 0.70 -
V V V V A A
Base-to-Emitter Voltage (Figure 2) Collector-to-Emitter Saturation Voltage (Figures 3, 4) Gain Bandwidth Product
VBE VCE SAT fT
VCE = 3V, IC = 10mA IC = 50mA, IB = 5mA VCE = 3V, IC = 10mA
V V MHz
FOR TRANSISTORS Q1 AND Q2 (As a Differential Amplifier) Absolute Input Offset Voltage (Figure 6) Absolute Input Offset Current (Figure 7) NOTE: 3. Actual forcing current is via the emitter for this test. |VIO| |IIO| VCE = 3V, IC = 1mA VCE = 3V, IC = 1mA 1.2 0.7 5 2.5 mV A
2
FN481.6 February 7, 2006
CA3083 Typical Performance Curves
DC FORWARD CURRENT TRANSFER RATIO 100 VCE = 3V TA = 70C TA = 25C TA = 0C 70 BASE-TO-EMITTER VOLTAGE (V) 0.9 VCE = 3V 0.8 TA = 0C TA = 25C TA = 70C 0.6
90
80
0.7
60
50 0.1 1 10 100 COLLECTOR CURRENT (mA)
0.5 0.1
1 10 COLLECTOR CURRENT (mA)
100
FIGURE 1. hFE vs IC
FIGURE 2. VBE vs IC
1
hFE = 10, TA = 25oC COLLECTOR-TO-EMITTER SATURATION VOLTAGE (V)
1.2 1 0.8 0.6 0.4 0.2 0 hFE = 10, TA = 70C
COLLECTOR-TO-EMITTER SATURATION VOLTAGE (V)
0.8
0.6
0.4 MAXIMUM 0.2 TYPICAL 0 1 10 COLLECTOR CURRENT (mA) 100
MAXIMUM TYPICAL
1
10 COLLECTOR CURRENT (mA)
100
FIGURE 3. VCE SAT vs IC
FIGURE 4. VCE SAT vs IC
hFE = 10, TA = 25C BASE-TO-EMITTER SATURATION VOLTAGE (V) 0.9
ABSOLUTE INPUT OFFSET VOLTAGE (mV)
1
6 VCE = 3V, TA = 25C 5 4 3 2 1 0 0.1 1 COLLECTOR CURRENT (mA) 10
0.8
0.7
0.6
0.5 1 10 COLLECTOR CURRENT (mA) 100
FIGURE 5. VBE SAT vs IC
FIGURE 6. VIO vs IC (TRANSISTORS Q1 AND Q2 AS A DIFFERENTIAL AMPLIFIER)
3
FN481.6 February 7, 2006
CA3083 Typical Performance Curves
ABSOLUTE INPUT OFFSET CURRENT (A) 10 VCE = 3V, TA = 25C
(Continued)
1
0.1
0.1
1 COLLECTOR CURRENT (mA)
10
FIGURE 7. IIO vs IC (TRANSISTORS Q1 AND Q2 AS A DIFFERENTIAL AMPLIFIER)
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com 4
FN481.6 February 7, 2006

▲Up To Search▲

Price & Availability of CA308306

	To Download CA308306 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .